Return-Path: X-Processed-By: Virex 7 on prxy.net X-Real-To: stagecraftlist [at] theatrical.net Received: by prxy.net (CommuniGate Pro PIPE 4.2.6) with PIPE id 4960278; Tue, 09 Nov 2004 03:01:06 -0800 X-ListServer: CommuniGate Pro LIST 4.2.6 List-Unsubscribe: List-ID: Message-ID: From: "Stagecraft" Sender: "Stagecraft" To: "Stagecraft" Precedence: list Subject: Stagecraft Digest #190 Date: Tue, 09 Nov 2004 03:00:53 -0800 MIME-Version: 1.0 Content-Type: text/plain; charset="ISO-8859-1" Content-Disposition: inline X-Spam-Checker-Version: SpamAssassin 3.0.1 (2004-10-22) on prxy.net X-Spam-Status: No, score=-2.6 required=5.0 tests=ALL_TRUSTED,AWL,BAYES_00, BIZ_TLD,RAZOR2_CHECK,URIBL_SBL autolearn=ham version=3.0.1 X-Spam-Level: X-TFF-CGPSA-Version: 1.4f2 X-prxy-Spam-Filter: Scanned For info, archives & UNSUBSCRIBE, see --------------------------------------------------- Stagecraft Digest, Issue #190 1. Re: Roadie Vests by "Nigel Worsley" 2. Re: Questionable Terminology by StevevETTrn [at] aol.com 3. Softcovered flats and wing bolts by "Dougherty, Jim" 4. Words of Wisdom by Heather Carter 5. Re: Softcovered flats and wing bolts by howie 6. Re: Questionable Terminology / now pan bolts by Greg Bierly 7. Re: Softcovered flats and wing bolts by Greg Bierly 8. Re: Drop shrinker/hardware question by "Wayne Rasmussen" 9. Re: Smoke pots: non pyro? by Dorian Kelly 10. Re: Questionable Terminology / now pan bolts by "Tony Deeming" 11. C-Clamp Hardware and Backdrop Shrinker by "Ken Mark" 12. Re: Questionable Terminology / now pan bolts by "Jonathan S. Deull" 13. Re: Lights falling from the sky by "John D. Palmer" 14. Re: Words of Wisdom by Stephen Litterst 15. Yoke bolts and pan bolts by Steve Larson 16. Speeding up time by doran [at] bard.edu 17. Re: Speeding up time by Jerry Durand 18. Re: Questionable Terminology / now pan bolts by Greg Bierly 19. Re: Words of Wisdom by "Dr. Randall W.A. Davidson" 20. Re: Speeding up time by "Joe Meils" 21. Re: C-Clamps and drops by "Mike Rock" 22. theatrical architecture by "K. Daly" 23. Re: UK Casual Pay comparison by 24. Re: Building Flats by 25. Re: UK Casual Pay comparison by "Tony Deeming" 26. Re: theatrical architecture by "Dr. Randall W.A. Davidson" *** Please update the subject line of your reply to use the subject *** line of the message you are replying to! Please only reply to *** one message subject in each reply. ---------------------------------------------------------------------- Message-ID: <00f501c4c58c$060e24a0$0c00a8c0 [at] Nigellaptop> From: "Nigel Worsley" Cc: danbutcher [at] ukpc.net References: Subject: Re: Roadie Vests Date: Mon, 8 Nov 2004 12:11:05 -0000 danbutcher [at] britishlibrary.net wrote: > Hi there, > Does anyoneone know where you can get a plain black (with possible a little > logo) roadie vest? There are several styles available here: http://www.site-electrics.co.uk/gaffergear.html No idea whether they are any good though. Nigel Worsley ------------------------------ From: StevevETTrn [at] aol.com Message-ID: <1ea.2ef4ad58.2ec0c267 [at] aol.com> Date: Mon, 8 Nov 2004 07:36:55 EST Subject: Re: Questionable Terminology >Impressing the importance of snugging those >bolts down once the unit is in focus... Given the wide variety of instrument hanging hardware, this is the best all around practice I can think of. Many of the "new" aluminum clamps do not have the pan setscrew at all. >I like to attach the safety cable to the instrument, >not the U piece holding the instrument. Some years ago, an architectural fixture came loose and fell (maintenance department's responsibility, not stage techs) and this resulted in a Risk Management edict to put safety cables on EVERYTHING. We had to run an aircraft cable through EVERY part of a fixture that could possibly be detached from the fixture. The yoke, the body, the lamp housing, the lens train, gel frame, gobo holder, and any other accessory, all had to be captive. This makes focusing, lamp changes and general maintenance a real hassle. Fortunately, the industry has become better at manufacturing fixtures with captive components and it is less of an issue for us now. SteveV Orl, FL ------------------------------ Date: Mon, 08 Nov 2004 09:04:04 -0500 Subject: Softcovered flats and wing bolts From: "Dougherty, Jim" Message-ID: For those secretly keeping a survey of who uses what, we are currently in a production for a show that has both muslin-covered hard theatrical flats and traditional soft covered flats. An unmentioned advantage to soft covered flats is that they also work as rear projection surfaces with the right fabric and color treatment (thick paint on canvas won't exactly work for that). And, for those neanderthals or neanderthals-in-training such as myself who delight in these things, we're lashing them together, too. Obsolete one might say, but in our scene changes no ladders are used to separate and strike flats up to 15' tall. LP hinges don't do that too well. Also, as someone else mentioned, we swap out the bitty pan bolts for t-handles (Colortran or other) as standard practice. You can also purchase loose t-handles for the bolt that attaches the c-clamp to the pipe, for toolless hang and focus without buying all new clamps; we don't go that far. If neither are an option, I like a speed wrench (ratcheting box end wrench for those looking through catalogs, and mine is from Sears) with a 5/8" and 3/4" end - one end works for the c-clamp, the other for the yoke bolt. There are also a lot of wrenches like these made specifically for lighting focus. Tools for Stagecraft, Production Advantage and Sapsis are just a few suppliers, and they'd all love your business. - Jim Dougherty ATD, Middlebury College Theatre Dept. ------------------------------ Date: Mon, 8 Nov 2004 09:09:59 -0500 Subject: Words of Wisdom From: Heather Carter Message-Id: Thanks for the words of wisdom for appropriate terminology for the f-nut. We will be referring to the questionable screw as a "pan bolt," since that will help re-inforce "tilt" and "pan". And we will be using them a lot, since, much like a place Dale (?) mentioned the instruments are not "happy"; fiddling with the yoke bolt can cause more trouble than fix it. If I can find all the stripped screws before they cause mucho frustration or cardiac arrest (and yes, we are safety chained-- point #2 I took care of when I took the job), both the instruments and I will be happier. (Thanks for the locking washer idea, June. Sounds like an esp. good fix for working with students.) --Heather. ------------------------------ Message-ID: <418F7F87.1090409 [at] hillinteractive.net> Date: Mon, 08 Nov 2004 09:15:35 -0500 From: howie Subject: Re: Softcovered flats and wing bolts References: In-Reply-To: Dougherty, Jim wrote: > For those secretly keeping a survey of who uses what, we are currently in a > production for a show that has both muslin-covered hard theatrical flats and > traditional soft covered flats. An unmentioned advantage to soft covered > flats is that they also work as rear projection surfaces with the right > fabric and color treatment (thick paint on canvas won't exactly work for > that). they are also lighter. One person can handle a fairly large softcovered flat. -----------------h ------------------------------ In-Reply-To: References: Message-Id: <360450B4-3191-11D9-9F35-000D936BFA94 [at] dejazzd.com> From: Greg Bierly Subject: Re: Questionable Terminology / now pan bolts Date: Mon, 8 Nov 2004 09:19:33 -0500 > I dearly love the T-handles the Colortran fixtures ship on their > clamps... I'm seriously considering purchasing them for my entire > inventory of new fixtures when my new theatres are built. S: I too > call them 'set screws' in appropriate company. > My former employer had had Clancy Sure-Clamps on every instrument in the hall with nylon washers on the yoke attachment. A true wrenchless hang. I converted my present theatre with nylon washers and t-handles on all c-clamps as a cheaper solution. Both have worked very well for me. The only time I touch a pan bolt is when I find one that has worked its way loose. Greg Bierly Technical Director Hempfield HS Greg Bierly Technical Director Hempfield HS ------------------------------ In-Reply-To: References: Message-Id: <6F52CA01-3191-11D9-9F35-000D936BFA94 [at] dejazzd.com> From: Greg Bierly Subject: Re: Softcovered flats and wing bolts Date: Mon, 8 Nov 2004 09:21:09 -0500 > they are also lighter. One person can handle a fairly large > softcovered flat. Which I prefer to fly in my educational setting. Greg Bierly Technical Director Hempfield HS ------------------------------ Message-ID: <002701c4c5a0$cb83fac0$0617000a [at] blair.edu> From: "Wayne Rasmussen" Subject: Re: Drop shrinker/hardware question Date: Mon, 8 Nov 2004 09:39:47 -0500 Thanks, Stephen. That clears it up. Wayne Rasmussen ------------------------------ Message-Id: In-Reply-To: References: Date: Mon, 8 Nov 2004 14:58:55 +0000 From: Dorian Kelly Subject: Re: Smoke pots: non pyro? >To get colors, you need dry particles. (The only way to make colored fog >is to color it with lighting.) Since you prefer not to use pyro, that >leaves tossing some type of pink and blue powder into the air. Just bear in mind that coloured smoke whether pyro or not is often a dye which can leave you and your stage worst for wear, and may be toxic as well. How well I remember FX1 Orange , not to be confused with Agent Orange (see Apocalypse Now for both) which left everything in sight either choking or looking as though they had just been locked in the spray tanning booth overnight Dorian ------------------------------ Message-ID: <001c01c4c5a5$97c62f00$0a01a8c0 [at] Tony> From: "Tony Deeming" References: Subject: Re: Questionable Terminology / now pan bolts Date: Mon, 8 Nov 2004 15:14:05 -0000 ----- Original Message ----- From: "Greg Bierly" To: "Stagecraft" Sent: Monday, November 08, 2004 2:19 PM Subject: Re: Questionable Terminology / now pan bolts > For info, archives & UNSUBSCRIBE, see > --------------------------------------------------- > > > I dearly love the T-handles the Colortran fixtures ship on their > > clamps... I'm seriously considering purchasing them for my entire > > inventory of new fixtures when my new theatres are built. S: I too > > call them 'set screws' in appropriate company. > > > > My former employer had had Clancy Sure-Clamps on every instrument in > the hall with nylon washers on the yoke attachment. A true wrenchless > hang. I converted my present theatre with nylon washers and t-handles > on all c-clamps as a cheaper solution. Both have worked very well for > me. The only time I touch a pan bolt is when I find one that has > worked its way loose. > > Greg Bierly > Technical Director > Hempfield HS > This confuses me just a little. Surely you use the pan bolt every time you use/re-use the instrument? Ynot ------------------------------ From: "Ken Mark" Subject: C-Clamp Hardware and Backdrop Shrinker Date: Mon, 8 Nov 2004 10:27:56 -0500 Message-ID: C-Clamp Hardware The Part number from Altman is 30-0031 The Description is 5/16-18 x 3/4 sq hd set screw steel plain I've always known it as the "Pan Bolt". Couldn't find it in any of my texts. List Price: $.55 (in 1996) As for rigging a backdrop that is too tall... I typically fold over the portion I don't need and put on a WHOLE LOT of LARGE SPRING Clamps. Every other foot seems to work nicely. Be CAREFUL. there is always the danger of tearing the drop. Just keep the clamp jaws on the pipe. ____ This is the Pipe (the spring clamp is represented by / the carats, just put them on from the TOP) || || || Down Stage || || | | | | | The 5' not needed is US with good side now FACING US Kenneth Mark Production Rentals Manager 439 County Route 45 Argyle, NY 12809 VOX: 518/761-3360 FAX: 518/761-3361 Mobile: 518/222-7750 On the Web at: www.adirondackscenic.com Visit the Production Rental On-Line Photo Album at: www.geocities.com/asikenmark ------------------------------ From: "Jonathan S. Deull" Subject: RE: Questionable Terminology / now pan bolts Date: Mon, 8 Nov 2004 10:34:46 -0500 In-Reply-To: Message-ID: In our high school setting where we want the kids to learn to use wrenches properly we use all of safety clamp, sidearm, Source 4 and Altman bolts just as they came out of the box, we use small tethered adjustable wrenches, and we emphasize -- as noted previously -- not overtightening. This is a life-skill. Jonathan S. Deull Edmund Burke School Washington, DC ------------------------------ Message-ID: <000001c4c5ae$4968e8d0$6501a8c0 [at] Toshiba2> From: "John D. Palmer" References: Subject: Re: Lights falling from the sky Date: Sun, 7 Nov 2004 10:52:21 -0800 One word... D*MN! >> The lights falling out of the yoke ( thanks for >> reminding me of the correct term, not very awake now, switching back to days from a week of overnight shifts. ) were due to the same lazy techs who would overtighten the tilt bolts, sometimes snapping them off, and then leaving the light hanging by the other one, which eventually snapped off. It was not a happy place to work when I was there, and I don't expect to ever go to that place again, having moved to another state. --Dale<< ------------------------------ Date: Mon, 08 Nov 2004 11:18:51 -0500 From: Stephen Litterst Subject: Re: Words of Wisdom Message-id: <418F9C6B.66062A46 [at] ithaca.edu> Organization: IC-Dept. of Theatre Arts References: Heather Carter wrote: > --------------------------------------------------- > > Thanks for the words of wisdom for appropriate terminology for the > f-nut. We will be referring to the questionable screw as a "pan bolt," > since that will help re-inforce "tilt" and "pan". And we will be using > them a lot, Just as an effort to convert more people to my mindset... I discourage the use of the pan bolt during focus. When that bolt pushes the barrel of the C-clamp to the side/front/whereever it disrupts the focus. And if there are a significant number of scars on the barrel, the pan bolt will often move the barrel until it fits into the nearest scar. Loosening the yoke bolt ever so slightly will allow you to pan the fixture without interfering with the tilt. And since most yoke bolts are 1" long, you have to really try to loosen it enough to have it fall out. Just my $.02. Steve L. -- Stephen C. Litterst Technical Supervisor Ithaca College Dept. of Theatre Arts 607/274-3947 slitterst [at] ithaca.edu ------------------------------ Date: Mon, 08 Nov 2004 12:12:27 -0500 Subject: Yoke bolts and pan bolts From: Steve Larson Message-ID: In-Reply-To: I believe that the confusion lies in that on many instrument C-Clamps, there are two bolts: the larger one which attaches the instrument yoke to the C-clamp, and smaller one which is threaded horizontally into the C-clamp. Loosening the horizontal bolt should not allow the yoke and instrument to fall. Loosening the larger bolt to the point that is falls away from the C-clamp will allow the yoke and instrument to fall. The safety cable should either go through the yoke or be attached directly to the instrument and then around the batten. I always instructed my university students and now whomever is working lights with me to only loosen the horizontal pan bolt. Some newer C-clamps do not have the horizontal bolt only the vertical bolt which attaches the yoke to the C-clamp. With these clamps, you should always have the safety cable properly fastened before loosening this bolt. Frankly, call it what you will. Just use them safely. Steve ------------------------------ Message-ID: <1099936203.418fb1cb21f81 [at] webmail.bard.edu> Date: Mon, 8 Nov 2004 12:50:03 -0500 From: doran [at] bard.edu Subject: Speeding up time Hey, all, For a production of "Yerma", the designer and director want us to speed up the clock. They want the mantle clock to run fast throughout the whole play, but wires are not feasable. Neither is a manual operation. I have a AA battery-operated quartz movement #TQ500P, manufactured by Walnut Hollow. Any suggestions would be greatly appreciated. Any suggestions that don't involve burning out the motor would be appreciated more. Thanks in advance, Andy Champ-Doran Technical Director Bard College Departments of Dance and Theater Annandale-on-Hudson, NY doran [at] bard.edu ------------------------------ Message-Id: <6.1.2.0.0.20041108095729.02e6a378 [at] localhost> Date: Mon, 08 Nov 2004 09:59:16 -0800 From: Jerry Durand Subject: Re: Speeding up time In-Reply-To: References: At 09:50 AM 11/8/2004, you wrote: >For a production of "Yerma", the designer and director want us to speed up >the clock. They want the mantle clock to run fast throughout the whole >play, but wires are not feasable. Neither is a manual operation. I have a >AA battery-operated quartz movement #TQ500P, manufactured by Walnut >Hollow. If it's only a little fast, most (all?) mechanical clock movements have a speed adjust someplace on them. If not, then you'll have to either re-wire the clock motor (the AA powered ones can have the coil driven by a PIC processor at any reasonable speed you want) or you need to replace the motor with a new one. Best if you don't need the clock to work right ever again. :) ---------- Jerry Durand Durand Interstellar, Inc. 219 Oak Wood Way Los Gatos, California 95032-2523 USA tel: +1 408 356-3886 fax: +1 408 356-4659 web: www.interstellar.com ------------------------------ In-Reply-To: References: Message-Id: <9AB732EE-31B2-11D9-9F35-000D936BFA94 [at] dejazzd.com> From: Greg Bierly Subject: Re: Questionable Terminology / now pan bolts Date: Mon, 8 Nov 2004 13:18:35 -0500 > This confuses me just a little. > Surely you use the pan bolt every time you use/re-use the instrument? > I tighten the yoke bolt as tight as it will go but the nylon washers allow the yoke to turn with a moderate amount of force without ever having to loosen the yoke bolt or pan bolt for that matter. The only situations that this can be a problem is when it the unit is not directly underhung, the unit is in danger of being bumped, or things have loosened up. I did spend a week replacing all of the nylon washers and nylon lock nut (Nylox?) on the Sure-clamps after 10+ years of service. I agree that the pan bolt effects focus too often. I never did give it a thought about the teaching aspect of wrenches. We do have a lot of situations though were the students still need a tethered wrench. The only other difficulty I found with a wrenchless hang is once everything was struck the crew didn't have wrenches for the incoming road show light plot. :-) Greg Bierly Technical Director Hempfield HS ------------------------------ From: "Dr. Randall W.A. Davidson" Subject: RE: Words of Wisdom Date: Mon, 8 Nov 2004 14:25:00 -0800 Message-ID: <009601c4c5e1$c9e666d0$726dfea9 [at] DrDoomsComputer> In-Reply-To: But are the instruments chained or secured, i.e. the body of the instrument, not just the c-clamp. doom ==================================================== A Masters Workshop for Entertainment Technicians, Riggers, Public Assembly Technicians, and Educational Performing Arts Personnel - Sponsored by Risk International & Associates, Inc. April 4, 5, 6, 2005 at ELCO Performing Arts Center, Elkhart, Indiana Brochure & Registration Form available at: www.riskit.com/workshops ==================================================== Risk International & Associates, Inc. - Dedicated to making the world a healthier & safer place. Website: www.riskit.com E-mail: rdavidson [at] riskit.com ==================================================== International Secondary Education Theater Safety Association (ISETSA) - Dedicated to the protection of every student in the performing arts. Website: www.isetsa.org E-mail: info [at] isetsa.org ==================================================== 960 E. Bonita #158, Pomona, CA 91767 Phone/Fax: (909) 625-5961 ==================================================== -----Original Message----- From: Stagecraft [mailto:stagecraft [at] theatrical.net] On Behalf Of Heather Carter Sent: Monday, November 08, 2004 6:10 AM To: Stagecraft Subject: Words of Wisdom For info, archives & UNSUBSCRIBE, see --------------------------------------------------- Thanks for the words of wisdom for appropriate terminology for the f-nut. We will be referring to the questionable screw as a "pan bolt," since that will help re-inforce "tilt" and "pan". And we will be using them a lot, since, much like a place Dale (?) mentioned the instruments are not "happy"; fiddling with the yoke bolt can cause more trouble than fix it. If I can find all the stripped screws before they cause mucho frustration or cardiac arrest (and yes, we are safety chained-- point #2 I took care of when I took the job), both the instruments and I will be happier. (Thanks for the locking washer idea, June. Sounds like an esp. good fix for working with students.) --Heather. ------------------------------ Message-ID: <000701c4c5ea$350118e0$04ecbed0 [at] hppav> From: "Joe Meils" References: Subject: Re: Speeding up time Date: Mon, 8 Nov 2004 17:25:16 -0600 We had a similar problem with a children's theatre production of "The Time Machine." What we did, after a lot of experimentation, was to rig a variable speed gear motor to the "reset" shaft. The rate could go anywhere from double time, up to a day passing in about a minute. The clock we were using was a large analog, rather like a classroom clock. It was a cheapie, so if we stripped the gears, it was no great loss. Joe UCA Theatre Conway, Arkansas ----- Original Message ----- From: To: "Stagecraft" Sent: Monday, November 08, 2004 11:50 AM Subject: Speeding up time > For info, archives & UNSUBSCRIBE, see > --------------------------------------------------- > > Hey, all, > > For a production of "Yerma", the designer and director want us to speed up > the clock. They want the mantle clock to run fast throughout the whole > play, but wires are not feasable. Neither is a manual operation. I have a > AA battery-operated quartz movement #TQ500P, manufactured by Walnut > Hollow. > > Any suggestions would be greatly appreciated. Any suggestions that don't > involve burning out the motor would be appreciated more. > > Thanks in advance, > Andy Champ-Doran > Technical Director > Bard College Departments of Dance and Theater > Annandale-on-Hudson, NY > doran [at] bard.edu > ------------------------------ Message-ID: <002301c4c5eb$2f8bbd10$80fea8c0 [at] Fred> From: "Mike Rock" References: Subject: Re: C-Clamps and drops Date: Mon, 8 Nov 2004 17:32:17 -0600 I can not recamend the use of clamps along to hold a drop. My freshman year we had the same problem and used spring clamps and c clamps to fix it. Half way through last dress there was a loud thoud and the whole fly system shook, turns out gravity overpowerd the clamps and the drop fell four or five feet and gatherd enough speed to strain the system. I hate to think what would have happend if a clamp would have fell or if it would have cause it to tear causing it to fall. ------------------------------ Message-Id: <6.1.2.0.2.20041108192901.01ce32e0 [at] mail.comcast.net> Date: Mon, 08 Nov 2004 19:31:25 -0500 From: "K. Daly" Subject: theatrical architecture In-Reply-To: References: An architecture student friend is making a project for his class out of re-designing a tired old theater. He knows architecture but not theater; can anyone recommend a good book for him on the unique needs of theaters when it comes to designing the structure? ------------------------------ From: Subject: Re: UK Casual Pay comparison Date: Mon, 8 Nov 2004 23:58:12 -0500 Message-Id: <20041109045813.LDSI347.fed1rmmtao02.cox.net [at] smtp.west.cox.net> >For the £4.60 the theatre want multi skilled techs but ends-up with lots of >stage weights. A four pound three shilling (is that correct old math?) stagehand is the going rate in Shakespeare's day. As I said, at that rate today, "Push this box over there" is the limit of the skills to be expected. Paying someone to rig at 4 pound sixty an hour is tantamount to manslaughter. Its just a matter of time. Chris Babbie OTRA Location Sound ------------------------------ From: Subject: RE: Building Flats Date: Mon, 8 Nov 2004 23:59:54 -0500 Message-Id: <20041109045956.IQQT18545.fed1rmmtao10.cox.net [at] smtp.west.cox.net> >We were doing "Dames at Sea" AAAAAAAUUUUUUUUGGGHHH! sorry... couldn't control it. Chris Babbie FMAO Location Sound ------------------------------ Message-ID: <003401c4c636$88db8d00$0a01a8c0 [at] Tony> From: "Tony Deeming" References: Subject: Re: UK Casual Pay comparison Date: Tue, 9 Nov 2004 08:31:36 -0000 ----- Original Message ----- From: To: "Stagecraft" Sent: Tuesday, November 09, 2004 4:58 AM Subject: Re: UK Casual Pay comparison > For info, archives & UNSUBSCRIBE, see > --------------------------------------------------- > > >For the £4.60 the theatre want multi skilled techs but ends-up with lots of > >stage weights. > > A four pound three shilling (is that correct old math?) stagehand is the going rate in Shakespeare's day. As I said, at that rate today, "Push this box over there" is the limit of the skills to be expected. Paying someone to rig at 4 pound sixty an hour is tantamount to manslaughter. Its just a matter of time. > > > Chris Babbie I must sayeth that I do be afraid that thy math doth not compute, dear heart. At twenty shillings for each pound in mine eyes, sixty shiny new pennies wilt come to no less than TWELVE shillings! I hopeth thiseth dotheth helpeth......! Ynoteth. ------------------------------ From: "Dr. Randall W.A. Davidson" Subject: RE: theatrical architecture Date: Tue, 9 Nov 2004 00:33:29 -0800 Message-ID: <013101c4c636$cad448a0$726dfea9 [at] DrDoomsComputer> In-Reply-To: Wow. Write me off line and I have about ten books. doom ==================================================== A Masters Workshop for Entertainment Technicians, Riggers, Public Assembly Technicians, and Educational Performing Arts Personnel - Sponsored by Risk International & Associates, Inc. April 4, 5, 6, 2005 at ELCO Performing Arts Center, Elkhart, Indiana Brochure & Registration Form available at: www.riskit.com/workshops ==================================================== Risk International & Associates, Inc. - Dedicated to making the world a healthier & safer place. Website: www.riskit.com E-mail: rdavidson [at] riskit.com ==================================================== International Secondary Education Theater Safety Association (ISETSA) - Dedicated to the protection of every student in the performing arts. Website: www.isetsa.org E-mail: info [at] isetsa.org ==================================================== 960 E. Bonita #158, Pomona, CA 91767 Phone/Fax: (909) 625-5961 ==================================================== -----Original Message----- From: Stagecraft [mailto:stagecraft [at] theatrical.net] On Behalf Of K. Daly Sent: Monday, November 08, 2004 4:31 PM To: Stagecraft Subject: theatrical architecture For info, archives & UNSUBSCRIBE, see --------------------------------------------------- An architecture student friend is making a project for his class out of re-designing a tired old theater. He knows architecture but not theater; can anyone recommend a good book for him on the unique needs of theaters when it comes to designing the structure? ------------------------------ End of Stagecraft Digest #190 *****************************